Changes to legislation in recent years mean that PPE (including safety boots and footwear) is provided by the employer at no cost to the worker. But with such an abundance of safety footwear on the market, it can be a daunting task working out exactly what your workforce needs and which products meet the requirements of the tasks and workers involved. Sole descriptions are varied, from ‘improving the grip performance’ to ‘excellent multi-directional slip-resistance’. Often, footwear is just described as ‘slip-resistant’ with no description of the conditions for which the footwear is most suitable.
When selecting footwear, you need to take into account several factors in addition to slip resistance, such as comfort, durability and any other safety features required, such as toe protection. Even the HSE suggest that the final choice may have to be a compromise.
Safety footwear – as with all types of PPE – should only ever be used as a ‘last resort’ when all other reasonable or practical measures have been taken to manage the risk involved. Before selecting safety footwear you should refer to a recent existing risk assessment for the workplace you are buying for, or carry one out if one does not already exist (more on this below).
Safety boots: the most common type of safety footwear, incorporating protective toe-caps with many other safety features including slip-resistant soles, penetration-resistant mid-soles and insulation against extremes of heat and cold.
Safety shoes: like safety boots, these usually have protective steel toe-caps although, as with safety boots, are available ‘metal free’ – so called composite footwear – which are lighter.
Safety trainers: perhaps considered more aesthetically appealing by wearers, these look more casual. Some have steel toe caps while others are plastic – referred to as composite toe caps (as above).
Riggers: these have been described as ‘a real stalwart of industrial footwear’4. A rigger boot is a particular type of pull-on safety boot; the name “rigger” comes from the fact that they were standard issue for workers on the offshore oil rigs in the North Sea, but are nowadays worn by most types of manual worker as a general purpose work boot. Concerns with this type of safety footwear have been raised, including a lack of ankle support.
Wellingtons: usually made of rubber and used for working in wet conditions, these are also useful in jobs where the footwear needs to be washed and disinfected for hygiene reasons, eg in the food and the chemical industries.
Clogs: these may also be used as safety footwear. They are traditionally made from beech wood and may be fitted with steel toe-caps and thin rubber soles for quieter tread.
Ladies ranges: safety footwear for women in a range of styles (boot, shoe, trainer) with the required key features such as steel toe caps, heat resistant midsoles and oil repellent soles.
Remember: manufacturers and suppliers have a key role in ensuring that suitable products are available and that companies have the information to enable them to make the right choice.
These Regulations seek to ensure that where risks cannot be adequately controlled by other means, Personal Protective Equipment (PPE) is correctly selected and used.
The Health and Safety at Work etc Act 1974 requires employers to ensure the health and safety of all employees and anyone affected by their work, so far as is reasonably practicable, which means balancing the level of risk against the measures needed to control the risk in terms of money, time or trouble. This includes taking steps to control slip and trip risks.
This Regulation requires that floors be suitable, in good condition and free from obstructions. People should be able to move around safely.
It is essential that procurers of footwear are sure that their chosen type will live up to the product description. 4All safety footwear has to meet certain requirements in line with European standards, that ensure the footwear has been tested effectively as stated by the standards and has certain properties that must be adhered to.
The quickest way to make sure any piece of footwear satisfies the “essential requirements” to protect workers as set out in the PPE Regulations is to be sure it is certified to the relevant EN standards.
The safety features of footwear are tested according to a set of European test standards written into EN ISO 20344:2004 (revised by ISO 20344:2011). The performance specifications are given in an associated set of standards, namely:
EN ISO 20345:2004 (replaced by 20345:2011 – see below) for safety footwear: specifies a standard of 200 joules impact resistance (equivalent to a 20kg weight dropped 1020mm onto the toes), and a 15KN compression test (equivalent to 1.5 tonnes resting on the toe area).
EN ISO 20346:2004 for protective footwear: specifies a lesser standard of 100 joules impact resistance, and a 10KN compression test.
EN ISO 20347:2004 for occupational footwear: can have many of the features of safety and/or protective footwear but without the safety toecap.
This replaces the older EN 20345:2004 and EN 345 standard on all new products. The earlier standards will still be seen on older stock but all new stock coming onto the market after June 2013 has to comply with EN 20345:2011. The relevant standard to which the footwear conforms will be identified on the footwear together with the level of protection provided. Footwear compliant with EN ISO 20345:2011 offers the greatest protection.
Special risks are covered by complementary job-related standards, for example footwear for firefighters, electrical insulating footwear, footwear protecting against chain saw injuries, chemicals, molten metal splash, and protection for motor cycle riders.
EN ISO 20345:2007 is the standard for footwear designed or retested after 2007. It sets out the minimum requirements that safety footwear must be successfully tested against.
EN ISO 20345:2011 applies to all footwear manufactured after 31 July 2013; these products must meet that standard. EN ISO 20345:2011 sets out tougher minimum requirements that safety footwear must be successfully tested against. The standard specifies that all safety footwear must have toe protection.
To make selection easier, safety boots and footwear normally carries a simple two or three letter code which defines the basic safety standards for that particular product. Typically this begins with an S for 200 Joule toe caps and less commonly P for 100 Joule toe caps; additional properties may be indicated by the use of further codes or pictograms.
As a basic requirement safety footwear must have a 200 joule toe cap. Other properties that may be included are: penetration resistance (midsole protection), conductive, anti-static, insulated against heat or cold, energy absorbing, outsole resistant to hot contact, water resistant.
Your toes are a very vulnerable part of your body, especially in a workplace. Toe protection must withstand a 200 joule impact. Joule is the unit of energy and this standard is purposefully specific. Something heavy falling from a low height could have a lot less energy than something lighter from a much higher height. As well as impacts, the toe area must withstand a resting mass of well over 1000kg.
Most people have heard of steel toe cap boots but the protection doesn’t have to be steel. In fact there are advantages to alternatives. Non-metallic protection can be equally as strong but lighter.
Clothing, seating materials, and climate factors can cause a build up a static charge of electricity in the body. Some materials in footwear can over insulate the body causing the charge to be held. When you then touch something the charge can rush from your body quickly causing a spark and a small uncomfortable shock. Antistatic footwear will significantly reduce this effect but does not offer full protection for exposure to electronics and explosives work. You will need Electro-Static Protection (ESD) for this.
Sharp objects where we walk and stand are a significant risk not only in the workplace but also outdoors and at home. Midsole protection will guard against nails and other objects. To meet this standard the footwear must be able to resist a penetration force of 1100N. Midsole protection is provided in one of these methods: a stainless steel insert in the sole, aluminium insert in the sole, or by Kevlar insole. The Aluminium and Kevlar solutions are the most flexible and lightest and cover the greatest area of the foot. Kevlar insoles also offer much higher thermal insulation.
ESD footwear is designed for the electronics and explosives industry and has to meet ESD CEI EN 61340-5-1 standard.
Safety footwear containing no metal parts is ideal for workplaces with metal detectors like airports, eliminating the hassle of removing them.
All safety footwear can have more features than are listed above but these are the minimum requirements to meet each of the safety ratings and the most common.
The HSE advise that you check with your supplier whether the footwear you are interested in has actually been tested for slip resistance – older models might not have been. Where footwear has been tested, coefficient of friction (CoF) test values must be available. CoF data can be requested from the supplier and must be included in the user instructions.. Some suppliers now publish it in their catalogues. The higher the CoF, the better the slip resistance. Look for CoF results higher than the minimum requirements set out in annex A of EN ISO 20345/6/7: 2004 (A1:2007).
The safety features of footwear, including slip resistance, are also tested according to a set of European test standards written into EN ISO 20344:2011 Personal protective equipment. Test methods for footwear.
Depending on the test conditions chosen, footwear tested according to the EN standards is now marked with one of the following codes: SRA, SRB, SRC.
PPE – including safety footwear – should only ever be used as a ‘last resort’ when all other reasonable or practical measures have been taken to manage the risk. It is crucial that the safety footwear you select:
This will give you a clear understanding of the hazards you need to protect against – and allow you to select the most appropriate safety footwear for your working environment. A risk assessment is a good way to identify new or missed hazards and to put measures in place to control them. The hazards may include:
Does the employee have any health concerns relevant to the safety footwear required; eg diabetes, plantar fasciitis, etc?
Concentrate on the real risks – those that are most likely to cause harm. Think about how accidents could happen and who might be harmed.
Ask your employees/colleagues what they think the hazards are – they may notice things that are not obvious to you and may have some good ideas on how to control the risks.
HSE’s Slips and Trips: Hazard Spotting Checklist www.hse.gov.uk/pubns/ck4.pdf is a useful resource that could help you to identify slip and trip hazards in your workplace and decide what action to take, be it the need for safety footwear or not.
PPE should also be periodically reviewed as new, improved styles may have become available and protective kit should be regularly checked for faults and properly maintained (more on this below) – staff should be encouraged to report faults or problems with their PPE.
Knowing the specific needs of your workplace environment is a key consideration. Is there a potential risk from falling objects, sharp surfaces or metals, or are chemicals or electrical hazards another potential risk?
As well as considering the hazards/risk involved in the job requiring safety footwear, procurers can also think about their industry – construction and healthcare sectors will have very different needs. For example:
When shopping for steel toe or composite boots/shoes you must be aware of the impact rating and compression rating:
Comfort and convenience to the wearer should be considered when selecting safety boots and footwear: employees should be consulted and be given a degree of choice, where appropriate, before final selection is made.
Footwear is worn for many hours each day, and so must offer comfort as well as safety; the fit must be right to ensure both.
As noted above, consultation with those wearing the PPE is crucial to make sure the correct PPE is chosen and that it is used and maintained properly.
Involving the end-users with regard to fit, comfort and wearability is likely to lead to better levels of user acceptance and therefore better protection.
Ensure any safety footwear you buy is ‘CE’ marked and complies with the requirements of the PPE Regulations. The CE marking signifies that the PPE satisfies certain basic safety requirements and in some cases will have been tested and certified by an independent body.
Some suppliers may offer ‘try before you buy’ on some products. This could be an important exercise in the procurement process; footwear marked ‘slip resistant’ may not perform well in your workplace for example, but you might not know that until you try the footwear out.
Others in your industry/job role may be able to advise on what has worked for them, or recommend certain products. This should only form part of your research however, as footwear should be selected for the job/environment/worker for whom you are procuring.
In addition to ensuring that safety boots meet the required legal standards it is also important to ensure it fits well. Poorly fitting safety footwear can result in bunions, corns, calluses, hammertoes, and other foot problems, and above all – safety footwear that does not fit may fail to prevent injury. So think about:
Upper – should be made from natural materials such as leather or a breathable man-made fabric. Some leather has a plastic coating to repel water and allow the shoe to be wiped clean.
Lining – should be a breathable material to keep the foot fresh. Linings need to be smooth and seam-free.
Toe area – should be foot-shaped and deep enough to prevent rubbing and allow the toes to wriggle. This is especially important with protective toecaps. If the shoes are padded and fitted properly, you should not be able to feel the toecaps at all.
Heel ﬁt – the heel should fit snugly on the foot, stopping the heel slipping out of the shoe and stabilising the foot upon ground contact.
Heel – should have a broad base and be no higher than 4cm. If worn for long stretches they should be no more than 2cm in height.
Sole – should be strong and flexible with shock absorption to cushion the jolts of walking on hard surfaces. Material should be slip resistant, such as rubber, polyurethane or PVC.
Consider the materials used to make the footwear as each material provides different levels of comfort, breathability, and durability. Examples include nylon mesh and leather, full grain leather, waterproof leather, Gore Tex.
PPE can often fall victim to cost management exercises because it can be seen as excessive or sometimes unnecessary ‘extras’ but is an area where cost cutting should be avoided. Good quality materials are a must and durability makes for a long lasting investment, rather than a short term cost.
Some companies still hesitate to purchase quality PPE and base product selection solely on the ‘up front price’ of each piece. While these companies may be able to reduce short term costs, they’re missing an opportunity to improve worker protection and enhance PPE performance.
Typically, companies get what they pay for when it comes to PPE. While lower quality footwear may cost less initially, it is likely to cost more in the long term if it needs to be replaced more frequently or if injury rates rise. Without the right protection against hazards, workplace accidents can increase.
An employer is legally responsible for protecting their workforce against injury and providing a safe working environment. Failing to do this could leave you vulnerable to expensive workplace injury claims.
It is a basic health and safety requirement that all PPE be supplied with instructions for use, and must carry the CE mark. The British Safety Industry Federation (BSIF) has put together a checklist that can help procurers of PPE spot potentially non-compliant products. The checklist asks:
BSIF also have available a CE Certificate Checklist to help you check that the PPE you have purchased is legal, its CE compliance certificate is genuine and that it relates directly to the performance of the equipment.
It is likely that you already have a trusted list of product suppliers. However, when looking for a new supplier/manufacturer it is work thinking about:
Crucially, make sure that suppliers/manufacturers supply products that are CE marked and display relevant EN codes; and have the required informative leaflets supplied with it. Talk to colleagues and peers who may be able to recommend suppliers that they use and trust.
As we know, one of the key points in safety boot procurement is considering the user. We’ve looked at comfort and convenience, and achieving the best fit. Another important consideration is whether or not the user has a condition that could influence your choice of footwear. Some to consider are:
Diabetic work shoes aim to provide protection against diabetic foot injury. They can be made from breathable leather or suede materials and are designed to cushion while providing ankle, arch, and heel support, and evenly distributing body weight across the foot to avoid painful pressure points. Diabetic work shoes can also provide the extra depth necessary to accommodate custom-orthotics which can prevent foot pain and provide comfort.
Ensure a correct fit for people who suffer with diabetes because poor fitting shoes, whether too loose or too tight, can cause rubbing leading to ulcers and further complications if not treated.
Many people with diabetes experience numbness and loss of sensation in their feet, thus it becomes even more critical that they wear correct fitting shoes to ensure that ulcers do not develop.
Comfort is key. Feet may change shape as people get older, and this is especially the case if they have arthritis – size and width fitting will be a consideration here.
Leather uppers are usually the most comfortable for people with foot problems; a flexible sole can also be better unless a doctor or podiatrist has advised that rigid soles are better for a particular foot problem.
For those with hammer toes or prominent joints, smooth lining without seams would be better. Consider that special insoles or orthoses may be needed; where used it must be ensured that there’s enough room to fit them in the safety shoes, especially around the toes.
Plantar fasciitis is injury to the tissue (fascia) that surrounds muscle and nerves on the bottom of the foot (plantar).
Excess weight that puts extra strain on the bottom of the foot, or standing for long periods of time, especially without good cushioning in the shoes, can also cause damage. Heel spurs are often seen with plantar fasciitis. Heel spurs are deposits of calcium on the underside of the heel that may or may not cause pain; the calcium is deposited after stress or injury. Heel spur and plantar fasciitis are sometimes linked together under the term Heel Spur Syndrome.
Things to check when buying a work boot is the amount of supportive cushioning, the ability of the boot to take extra cushioning in the form of inserts or custom-made orthotics and how well the boot fits the needs of the job.
Wide fittings include 2E (wide), 4E (extra wide) and 6E (extra, extra wide).Ensure the footwear has relevant safety features, such as steel or composite toe caps. Wider styles can vary from wide safety shoes, boots and trainers.
When selecting safety boots, think about the surface type on which the footwear will be worn. Footwear alone will not eliminate slips on contaminated surfaces – there are several factors that may contribute to an accident and good housekeeping can help to prevent incidents. Selecting footwear carefully however, to ensure basic tread pattern design and consideration of friction levels, will help to minimise the risk of slips.
The PPE Regulations require that PPE is properly assessed before use to make sure it is fit for purpose; and to ensure that it is maintained and stored properly.
While the selection of safety boots and footwear appropriate to the wearer, environment and demands of the job is essential to ensuring that it provides the proper protection, inspecting the footwear for signs that it may need to be replaced is also crucial.
There’s no one-size-fits-all formula for knowing exactly when it’s time to replace safety shoes, as there are many variables to consider such as the job hazards, how often the boot is worn and the size and weight of the worker. However if there’s any doubt that the shoe is no longer performing as it should, then it should be replaced.
When inspecting safety footwear to see if it needs to be replaced, shoes with steel toecaps may show more obvious signs of damage or wear than shoes with composite material toecaps. For example, if a heavy object falls on a steel toe shoe, the steel cap will be dented and will not ‘spring back’, suggesting that the shoe must be replaced. Conversely, composite material shoes could still be damaged in the same incident but maintain their form.
Consider the tread on a slip-resistant safety shoe – once the tread or outsole show signs of wear or damage, the shoe is likely to need replacing.
The HSE advise that PPE must be properly looked after and stored when not in use, e.g. in a dry, clean cupboard. If it is reusable it must be cleaned and kept in good condition.
In general, PPE should be examined to ensure it is in good working order before being issued to the user. Such examinations should be carried out by appropriately trained staff. It should not be issued if found to be defective.
Employers can ask employees to clean their own PPE, but it is advised that this be stipulated in the person’s contract of employment. The employer would need to ensure proper cleaning instructions are provided so there is no damage and the employer should arrange for spot checks to ensure PPE is suitable.
The HSE’s L25 document notes that PPE will have a useable ‘shelf life’. When it exceeds this shelf life or is so badly damaged that repair is not possible or too costly then it needs to be replaced.
The procurement of safety boots and footwear is only the first stage in a continuing programme involving risk assessment, employee consultation, training and supervision to ensure proper use, and inspection and maintenance of the product.
Safety footwear that is not appropriate may fail to prevent injury and cause foot problems. Select the right product based on your risk assessment and consultation with your team – make sure they’re comfortable wearing the product. Then educate them in the why and the how and make sure you have a regime to monitor and evaluate continuously.
Anti-Static Work Shoes
[…] all that could take place at your workplace. Look into the ladies steel cap boots now in order to locate cost-effective, comfortable, as well as protective shoes it is possible to wear to work every single day to be […]
Good Job, excellent article, I loved it the way that you explained about footwear for safety purpose.
Fur turning rubber sole, Imitation ox tendon sole, Injection molded sole - Aonaibao,https://www.aonaibao.com/